收藏本站
315MHz/434MHz Low-Power, 3V/5V
ASK/FSK Superheterodyne Receiver
Table 7. Configuration Register (Address: 0x1)
BIT ID
X
BIT NAME
Don’t care
BIT LOCATION
(0 = LSB)
7
POWER-UP
STATE
0
Don’t care.
FUNCTION
0 = LNA low-gain state.
1 = LNA high-gain state.
GAINSET
Gain set
6
1
For manual gain control, enable the AGC (AGC_EN =
1), set LNA gain state to desired setting, then disable
the AGC (AGC_EN = 0).
FSKCALLSB = 1 enables a longer, more accurate
FSKCALLSB
FSK accurate
calibration
5
0
FSK calibration.
FSKCALLSB = 0 provides for a quick, less accurate
FSK calibration.
This bit enables the FDATA pin to act as the serial
DOUT_FSK
FSKOUT enable
4
0
data output in 4-wire mode. (See the Communication
Protocol section.)
This bit enables the ADATA pin to act as the serial
DOUT_ASK
ASKOUT enable
3
0
data output in 4-wire mode. (See the Communication
Protocol section.)
TOFF_PS1
TOFF_PS0
Off-timer prescale
Off-timer prescale
2
1
0
0
Sets LSB size for the off timer. (See the Off Timer
section.)
1 = Discontinuous receive mode. (See the
DRX_MODE
Receive mode
0
0
Discontinuous Receive Mode section.)
0 = Continuous receive mode. (See the Continuous
Receive Mode section.)
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. On high-frequency inputs and
outputs, use controlled-impedance lines and keep
them as short as possible to minimize losses and radia-
tion. At high frequencies, trace lengths that are on the
order of λ /10 or longer act as antennas.
Keeping the traces short also reduces parasitic induc-
tance. Generally, 1in of a PCB trace adds about 20nH
of parasitic inductance. The parasitic inductance can
have a dramatic effect on the effective inductance of a
passive component. For example, a 0.5in trace con-
necting a 100nH inductor adds an extra 10nH of induc-
tance or 10%.
To reduce the parasitic inductance, use wider traces
and a solid ground or power lane below the signal
traces. Also, use low-inductance connections to ground
on all GND pins, and place decoupling capacitors
close to all V DD or HVIN connections.
22
______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX1472EVKIT-433# EVAL KIT MAX1472
MAX1473EVKIT-433 EVAL KIT MAX1473
MAX1479EVKIT-315 EVAL KIT FOR MAX1479 315MHZ
MAX19700EVKIT EVAL KIT FOR MAX19700
MAX19985AETX+T IC MIXER DOWNCONV 36-TQFN-EP
MAX19993ETX+ IC MIXER DOWNCONV 36TQFN
MAX19994AEVKIT# KIT EVAL FOR MAX19994A MIXER
MAX19995ETX+T IC DOWNCONVERTER 2CH 36TQFN
相关代理商/技术参数
MAX1471EVKIT-433 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471EVSYS-315 功能描述:射频开发工具 MAX1471 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MAX1471EVSYS-433 功能描述:射频开发工具 MAX1471 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MAX1472AKA 制造商:Maxim from Components Direct 功能描述:MAXIM MAX1472AKA RF ICS MISC - Tape and Reel 制造商:Maxim 功能描述:Maxim MAX1472AKA RF ICs Misc
MAX1472AKA+ 制造商:Maxim Integrated Products 功能描述:LOW-PWR CRYSTAL-BASED ASK TRANSMITTER 8PIN SOT-23 - Rail/Tube
MAX1472AKA+T 功能描述:射频发射器 300-450MHz Low-P Crystal-Based ASK RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel
MAX1472AKA-T 功能描述:射频发射器 RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel
MAX1472AKA-TG05 功能描述:射频发射器 300-450MHz Low-P Crystal-Based ASK RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel